November 3rd, 2011
I have a patch queue that looks roughly like:
initial-API consumer-1 consumer-2 unrelated consumer-3-plus-API-changes-and-consumer-1-and-2-updates-for-new-API
(So my base repo has a patch ‘initial-API-changes’ applied to it, followed by a patch ‘consumer-1′, etc.)
The idea is that I am working on a new API of some sort, and have a couple of independent consumers of that API. The first two are “done”, but when working on the 3rd, I realize that I need to make changes to or clean up the API that they’re all using. So I hack away, and end up with a patch that contains both consumer 3 plus some API changes, and to get it to compile I also update consumers 1 and 2 to accommodate the new changes. All of that is rolled up into a big hairball of a patch.
Now, what I want is:
final-API consumer-1 (new API) consumer-2 (new API) unrelated consumer-3 (new API)
But how do I do that (using mq patches)? I can use qcrefresh+qnew to fairly easily get to:
initial-API consumer-1 (old API) consumer-2 (old API) unrelated consumer-3 (new API) API-changes-plus-API-changes-for-consumers-1-and-2
or I could split out the consumer 1 & 2 API changes:
initial-API consumer-1 (old API) consumer-2 (old API) unrelated consumer-3 (new API) API-changes consumer-2-API-changes consumer-1-API-changes
which theoretically I could qfold the consumer 1 and consumer 2 patches:
initial-API consumer-1 (new API) consumer-2 (new API) unrelated consumer-3 (new API) API-changes
Unfortunately, consumer-1-API-changes collides with API-changes, so the fold will fail. It shouldn’t collide, really, but it does because part of the code to “register” consumer-1 with the new API happens to sit right alongside the API itself. Even worse, how do I “sink” the ‘API-changes’ patch down so I can fold it into initial-API to produce final-API? (Apologies for displaying my stacks upside-down from my terminology!) A naive qfold will only work if the API-changes stuff is separate from all the consumer-* patches.
My manual solution is to start with the initial queue:
initial-API consumer-1 (old API) consumer-2 (old API) unrelated consumer-3-plus-API-changes-and-consumer-1-and-2-updates-for-new-API
and then use qcrefresh to rip the API changes and their effects on consumers 1 & 2 back out, leaving:
initial-API consumer-1 (old API) consumer-2 (old API) unrelated API-changes-and-consumer-1-and-2-updates-for-new-API (in working directory) consumer-3 (new API)
I qrename/qmv the current patch to ‘api-change’ and qnew ‘consumer-3′ (its original name), cursing about how my commit messages are now on the wrong patch. Now I have
initial-API consumer-1 (old API) consumer-2 (old API) unrelated api-change (API changes and consumer 1 and 2 updates for new API) consumer-3 (new API)
Now I know that ‘unrelated’ doesn’t touch any of the same files, so I can qgoto consumer-2 and qfold api-change safely, producing:
initial-API consumer-1 (old API) consumer-2 (new API, but also with API change and consumer 1 updates) unrelated consumer-3 (new API)
I again qcrefresh,qmv,qnew to pull a reduced version of the api-change patch, giving:
initial-API consumer-1 (old API) api-change (with API change and consumer 1 updates) consumer-2 (new API) unrelated consumer-3 (new API)
Repeat. I’m basically taking a combined patch and sinking it down towards its destination, carving off pieces to incorporate into patches as I pass them by. Now I have:
initial-API api-change (with *only* the API change!) consumer-1 (new API) consumer-2 (new API) unrelated consumer-3 (new API)
and finally I can qfold api-change into initial-API, rename it to final-API, and have my desired result.
What a pain in the ass! Though the qcrefresh/qmv/qnew step is a lot better than what I’ve been doing up until now. Without qcrefresh, it would be
% hg qrefresh -X . % hg qcrecord api-change % hg qnew consumer-n % hg qpop % hg qpop % hg qpop % hg qpush --move api-change % hg qpush --move consumer-n % hg qfold old-consumer-n
which admittedly preserves the change message from old-consumer-n, which is an advantage over my qcrefresh version.
Or alternatively: fold all of the patches together, and qcrecord until you have your desired final result. In this particular case, the ‘unrelated’ patch was a whole series of patches, and they weren’t unrelated enough to just trivially reorder them out of the way.
Without qcrecord, this is intensely painful, and probably involves hand-editing patch files.
My dream workflow would be to have qfold do the legwork: first scan through all intervening patches and grab out the portions of the folded patch that only modify nonconflicting files. Then try to get clever and do the same thing for the portions of the conflicted files that are independent. (The cleverness isn’t strictly necessary, but I’ve found that I end up selecting the same portions of my sinking patch over and over again, which gets old.) Then sink the patch as far as it will go before hitting a still-conflicting file, and open up the crecord UI to pull out just the parts that belong to the patch being folded (aka sunk). Repeat this for every intervening conflicting patch until the patch has sunk to its destination, then fold it in. If things get too hairy, then at any point abort the operation, leaving behind a half-sunk patch sitting next to the unmodified patch it conflicted with. (Alternatively, undo the entire operation, but since I keep my mq repo revision-controlled, I don’t care all that much.)
I originally wanted something that would do 3-way merges instead of the crecord UI invocations, but merges really want to move you “forward” to the final result of merging separate patches/lines of development. Here, I want to go backwards to a patch that, if merged, would produce the result I already have. So merge(base,base+A,base+B) -> base+AB which is the same as base+BA. From that, I could infer a B’ such that base+A+B’ is my merged base+AB, but that doesn’t do me any good.
In my case, I have base+A+B and want B” and A” such that base+B”+A” == base+A+B.
To anyone who made it this far: is there already an easy way to go about this? Is there something wrong with my development style that I get into these sorts of situations? In my case, I had already landed ‘initial-API’; please don’t tell me that the answer is that I always have to get the API right in the first place. Does anyone else get into this mess? (I can’t say I’ve run into this all that often, but it’s happened more than once or twice.)
I suppose if I had landed consumers 1 and 2, I would’ve just had to modify their uses of the API afterwards. So I could do that here, too. But reviews could tangle things up pretty easily — if a reviewer of consumer 1 or 2 notices the API uglinesses that I fixed for consumer 3, then landing the earlier consumers becomes dependent on landing consumer 3, which sucks. But also, none of this is really ready to land, and I’d like to iterate the API in my queue for a while with all the different consumers as test users, *without* lumping everything together into one massive patch.